Easy Assembly Guide for the Autonomous SmartDesk Core

Table of Contents:

1. Introduction
2. Step 1: Loosen the screws on the cross piece
3. Step 2: Attaching the legs to the cross Beam
4. Step 3: Attaching the feet to the legs
5. Step 4: Attaching the side brackets
6. Step 5: Adding Rubber cushions
7. Step 6: Flipping the frame and attaching it to the work surface
8. Step 7: Attaching the control box
9. Step 8: Attaching the control switch and power cable
10. Conclusion

How to Assemble the Autonomous SmartDesk Core

Introduction

In this guide, I will Show You step-by-step how to assemble the Autonomous SmartDesk Core. This desk is known for its easy assembly process, which typically takes between 15 to 30 minutes. By following these instructions, you'll be able to assemble your SmartDesk Core efficiently and effectively.

Step 1: Loosen the screws on the cross piece

To begin the assembly process, loosen the screws on the cross piece of the desk using a tape measure and a smaller allen wrench. This will allow the frame to adjust to the width of the desktop you are using. Aim for a width of approximately 46 inches, leaving about an inch of overhang on each side of the leg.

Pros: Easy to adjust the width according to your desktop size. Allows for flexibility in desk customization.

Cons: Loosening the screws can be time-consuming and requires Attention to Detail.

Step 2: Attaching the legs to the cross beam

Next, Align the legs with the cross beam and secure them using smaller screws and the smaller allen wrench. Make sure to position the screws facing towards the top for easy installation. Attach the legs one by one, ensuring a tight fit. Use the allen wrench to tighten the screws securely.

Pros: Sturdy attachment of the legs to the cross beam. Provides stability to the desk.

Cons: Requires some maneuvering to align the legs with the screws properly.

Step 3: Attaching the feet to the legs

Attach the feet to the legs using larger screws and the larger allen wrench. The feet can be attached to either leg and can face any direction. It is recommended to start by HAND-tightening the screws and then using the allen wrench to ensure a secure fit.

Pros: Allows for easy customization of the desk according to personal preferences. Provides additional stability to the desk.

Cons: Requires careful alignment of the feet with the legs.

Step 4: Attaching the side brackets

Attach the side brackets to the side of the frame using smaller screws and the smaller allen wrench. The brackets should hang on the side of the frame in an L-Shape. Begin by lining up the screws and securing them one by one using the allen wrench.

Pros: Enhances the structural integrity of the desk. Provides additional support to the frame.

Cons: Requires attention to detail to align the brackets properly.

Step 5: Adding rubber cushions

Insert the black rubber cushions into the holes on the brackets. These cushions help with noise reduction and prevent the legs from getting caught in the cables underneath the desk. Ensure that the cushions are properly inserted into all the designated holes.

Pros: Reduces noise during desk movement. Prevents leg entanglement with cables.

Cons: None.

Step 6: Flipping the frame and attaching it to the work surface

Carefully flip the frame upside down and place it on top of the work surface. Use screws to attach the frame to the work surface, ensuring that there are no gaps between the frame and the surface. This step may require assistance from another person due to the weight of the frame.

Pros: Secures the frame to the work surface. Provides stability to the desk.

Cons: Requires careful handling due to the weight of the frame.

Step 7: Attaching the control box

Attach the control box to the bottom side of the work surface using screws. Place the control box closer to the backside of the desk for easier access. Use the same screws used to attach the frame to the work surface.

Pros: Convenient access to the control box. Ensures the control box is securely attached.

Cons: None.

Step 8: Attaching the control switch and power cable

Attach the control switch to the front side of the desk using small screws. Choose the side of the desk where you want the switch to be located. Connect the motor cables, switch cable, and power cord to their corresponding slots and secure them in place. Use cable ties to organize and secure the cables underneath the desk for a neat and tidy appearance.

Pros: Easy access to the control switch. Neat and organized cable management.

Cons: None.

Conclusion

Congratulations! You have successfully assembled your Autonomous SmartDesk Core. This desk offers a seamless assembly process with instructions that are easy to follow. Enjoy the benefits of a well-built, adjustable desk that enhances your ergonomic workspace.

Highlights

• Easy and efficient assembly process
• Sturdy construction and stability
• Customizable features for personalized preferences
• Noise reduction with rubber cushions
• Neat and organized cable management

FAQ

Q: How long does it take to assemble the Autonomous SmartDesk Core?

A: The assembly process typically takes between 15 to 30 minutes, depending on your familiarity with the instructions and tools.

Q: Can I use a power drill for assembly?

A: While it is possible to use a power drill, it is recommended to use the provided allen wrench to avoid over-tightening and damaging the screws.

Q: Can I customize the width of the desk?

A: Yes, the desk allows you to adjust the width to fit your specific desktop size, providing flexibility in desk customization.

Q: How do I reset the control box?

A: To reset the control box, hold down the up and down buttons simultaneously until the desk moves down to its lowest position, and then shows the Height on the display.