Troubleshooting Sony VO 9850 Error Code 02 042021
Table of Contents
- Introduction
- Overview of the Pneumatic VO 9850 Recorder
- Error 2 Code: Loading Issue
- The Culprit: Malfunctioning Sensor
- Fixing the Loading Issue
- Removing the Top Panel
- Adjusting the Misaligned Sensor
- Troubleshooting Tape Stuck Issue
- Resetting the Machine
- Testing the Recorder
- Additional Maintenance: Belts Replacement
- Conclusion
Introduction
In this article, we will be discussing the Pneumatic VO 9850 Recorder - an ancient piece of gear that has been causing trouble due to an error 2 code related to tape loading. We will explore the main cause of this issue and provide a step-by-step guide on how to fix it. Additionally, we will touch upon other maintenance tasks, such as belt replacements, to ensure optimal performance of the recorder.
Overview of the Pneumatic VO 9850 Recorder
The Pneumatic VO 9850 Recorder is a classic device that has seen many years of use. However, like any other mechanical equipment, it is susceptible to malfunctions over time. One common problem users face is an error 2 code, specifically related to the loading mechanism of the tape. When attempting to play a tape, the recorder fails to Sense that it has been fully drawn into the mechanism, resulting in an error. Fortunately, this issue can be resolved by addressing the malfunctioning sensor.
Error 2 Code: Loading Issue
The error 2 code in the Pneumatic VO 9850 Recorder is specifically related to the loading of tapes. While the machine functions correctly during rewinding, fast-forwarding, or ejecting, it fails to detect the tape after hitting the play button. This faulty detection is primarily caused by a misaligned sensor responsible for sensing the tape's position within the mechanism.
The Culprit: Malfunctioning Sensor
Upon further investigation, it becomes evident that the main culprit of the loading issue is a misaligned sensor. This sensor, located in the loading mechanism, fails to sense when the tape has been fully drawn into the mechanism. This misalignment leads to the error 2 code when attempting to play a tape.
Fixing the Loading Issue
To resolve the loading issue in the Pneumatic VO 9850 Recorder, follow these steps:
- Removing the Top Panel: Begin by removing the screws to detach the top panel of the recorder. This will provide access to the internal components.
- Adjusting the Misaligned Sensor: Locate the misaligned sensor within the loading mechanism. With caution, adjust the sensor by slightly rotating it to ensure proper alignment.
- Troubleshooting Tape Stuck Issue: In the case of a tape being stuck within the mechanism, manually rotate the wheel to release the tape, allowing it to fully unload.
- Resetting the Machine: Power off the recorder and then turn it back on to reset the system after resolving the tape loading issue.
By carefully following these steps, the loading issue should be resolved, and the recorder should function properly once again.
Testing the Recorder
Once the loading issue has been addressed, it is crucial to test the functionality of the Pneumatic VO 9850 Recorder. Connect the recorder to a monitor and ensure that it is rewinding, fast-forwarding, playing, and ejecting tapes without any errors. This thorough testing will validate the effectiveness of the repair and confirm that the recorder is operating as intended.
Additional Maintenance: Belts Replacement
While troubleshooting the loading issue, it is a good opportunity to inspect the condition of the belts within the Pneumatic VO 9850 Recorder. If the belts Show signs of wear or deterioration, it is recommended to replace them to ensure optimal performance. Belt replacement can be performed using standard maintenance procedures, and video tutorials are available for reference.
Conclusion
In conclusion, the Pneumatic VO 9850 Recorder is a vintage piece of equipment that may encounter issues with tape loading, resulting in an error 2 code. By addressing the malfunctioning sensor and following the step-by-step guide provided in this article, users can resolve the loading issue and restore the functionality of the recorder. Additionally, it is essential to perform regular maintenance, such as belt replacements, to keep the recorder in optimal condition for extended use.
Highlights
- The Pneumatic VO 9850 Recorder is an ancient gear that may encounter error 2 code related to tape loading.
- The error 2 code is primarily caused by a misaligned sensor within the loading mechanism.
- Fixing the issue involves adjusting the sensor's alignment, troubleshooting tape stuck issues, and performing a reset.
- Thorough testing should be conducted to ensure the loading issue has been resolved.
- Regular maintenance, including belt replacements, is necessary to keep the recorder in optimal condition.
FAQs
Q: How can I fix the error 2 code in my Pneumatic VO 9850 Recorder?
A: To fix the error 2 code, you need to address the misaligned sensor in the loading mechanism. Follow the step-by-step guide provided in this article.
Q: What should I do if a tape gets stuck in the recorder?
A: In case of a tape being stuck, manually rotate the wheel to release the tape and allow it to fully unload.
Q: Are belt replacements necessary for optimal performance?
A: Yes, regular belt replacements are recommended to ensure the optimal performance of the Pneumatic VO 9850 Recorder.