Master the Anafi AI: Your Guide to a Successful First Flight

Master the Anafi AI: Your Guide to a Successful First Flight

Table of Contents:

1. Introduction
2. Connecting the Smart Device to Sky Controller 4
3. Sky Controller 4 Functions
4. Camera Controls
5. Setting up the Anafi AI for Flight
6. Pre-flight Checklist
7. Using the Free Flight 7 Application
8. Completing a Compass Calibration
9. Setting Return to Home Functions
10. Taking Off and Controllability Check
11. Safety Features associated with Takeoff Button
12. Testing Camera Functions
13. Landing the Aircraft
14. Conclusion

Introduction

Welcome to the Parrot's training video series for the Anafi AI. In this article, we will guide You through the process of taking your aircraft on its first flight. Before we begin, it's important to ensure that your system is updated, calibrated, and that you have a brief understanding of the Free Flight 7 application.

Connecting the Smart Device to Sky Controller 4

To start, you'll need to connect your smart device to the Sky Controller 4. Use the USB-C cable to plug it into the USB-C port on the side of the controller. Loop the cable through the controller to connect your smart device. Once connected, you can expand the controller to hold it properly.

Sky Controller 4 Functions

The Sky Controller 4 offers various functions that control the aircraft. On the right-HAND side of the controller, you'll find the power button. Press and hold it for four seconds to power on. On the left-hand side, there are buttons for takeoff and landing, as well as the return to home function. The left control stick controls altitude and yaw, while the right control stick controls roll and pitch. Additionally, there are camera controls for optics reset, gimbal control, recording/shutter, and zooming.

Camera Controls

The camera controls on the Sky Controller 4 allow you to manage the Anafi AI's camera functions. You can reset the optics, control the gimbal up or down, Record or take a picture, and zoom in or out.

Setting up the Anafi AI for Flight

Before taking flight, it's essential to properly set up the Anafi AI. Find a suitable location and open your case to retrieve the aircraft. Remove the gimbal lock to allow the camera and obstacle avoidance system to move freely. Extend the arms and inspect the propellers to ensure they are ready for flight.

Pre-flight Checklist

Power on the Anafi AI by holding the power button for five seconds. You'll hear the aircraft's four motors beep, followed by a gimbal calibration to prepare the camera for flight. Next, power on the Sky Controller 4 by holding the power button for four seconds. Once the system is connected, the blinking of the Sky Controller will stop, and the Free Flight 7 application should open automatically. Before takeoff, complete a compass calibration and set the return to home functions Based on your preferences.

Using the Free Flight 7 Application

The Free Flight 7 application provides essential information and controls for your Anafi AI. Verify that you are logged into your Parrot Cloud and PIX4D accounts. Check that the controller has GPS and that the tablet and controller are fully charged. Ensure that both the controller and aircraft are updated. The application also displays the aircraft's connectivity status, battery level, and other important details.

Completing a Compass Calibration

Performing a compass calibration is crucial to ensure accurate flight control. Select the aircraft from the Free Flight 7 application and navigate to the calibrations section. Follow the on-screen instructions to complete the compass calibration process.

Setting Return to Home Functions

Before each flight, pilots must set their preferred return to home functions. Choose whether you want the aircraft to return to the takeoff point, hover, land, and at what altitude it should return. Set these functions in the Free Flight 7 application.

Taking Off and Controllability Check

To take off, press the takeoff button on the left-hand side of the controller. The aircraft will launch into a stabilized hover. Observe the obstacle avoidance shield, which will change color from red to green when obstacle avoidance is active. Monitor the pilot's distance from the aircraft, altitude, battery levels, and connectivity status on the heads-up display of the Free Flight 7 application. Perform a controllability check by moving each stick one at a time to ensure all controls are functioning properly.

Safety Features associated with Takeoff Button

The takeoff button has safety features to prevent accidental actions. If the button is pressed unintentionally, it can be pressed again to cancel the takeoff. Similarly, if the button is pressed during flight, it can be pressed again to abort the landing and return the aircraft to its position.

Testing Camera Functions

Once comfortable with the flight controls, you can test the camera functions. Use the controls on the Sky Controller 4 to adjust the gimbal, take pictures or record videos, and zoom in or out. This is an excellent opportunity to familiarize yourself with the camera capabilities of the Anafi AI.

Landing the Aircraft

When the flight is complete, it's time to land the aircraft. Press the landing button on the controller and adjust the landing vector using the control sticks as needed. If desired, activate the aircraft's return to home function, ensuring it is properly set up before activation.

Conclusion

Congratulations on successfully taking your Anafi AI on its first flight! In the next videos, we will dive deeper into the different piloting modes found in the Free Flight 7 application. Stay tuned to Parrot's training videos for more tips and guides on mastering your Anafi AI.

Highlights

1. Learn how to connect your smart device to the Sky Controller 4.
2. Understand the functions of the Sky Controller 4.
3. Explore the camera controls and features.
4. Properly set up the Anafi AI for flight.
5. Complete the pre-flight checklist and calibrate the compass.
6. Set the return to home functions based on your preferences.
7. Takeoff, perform a controllability check, and engage obstacle avoidance.
8. Understand the safety features associated with the takeoff button.
9. Test the camera functions and explore the Anafi AI's capabilities.
10. Safely land the aircraft and activate the return to home function.

FAQ

Q: How do I connect my smart device to the Sky Controller 4? A: Use a USB-C cable to connect your smart device to the USB-C port on the side of the controller.

Q: How do I perform a compass calibration? A: Select the aircraft in the Free Flight 7 application, go to calibrations, and follow the on-screen instructions.

Q: Can I abort the landing if the landing button is pressed accidentally? A: Yes, you can press the landing button again to abort the landing.

Q: How do I adjust the landing vector when landing the aircraft? A: Use the control sticks on the Sky Controller 4 to adjust the landing vector as needed.

Q: What are the safety features associated with the takeoff button? A: If the takeoff button is pressed accidentally, it can be pressed again to cancel the takeoff or abort the landing if pressed during flight.