Easy Installation Guide for Corsair H100i PRO RGB on AMD (AM4)

Table of Contents

1. Introduction
2. Unboxing the Corsair H100 I Pro
3. Installing the AMD Mounting Bracket
4. Attaching the Water Block and Pump Unit
5. Mounting the Fans to the Radiator
6. Installing the Radiator to the Case
7. Plugging in the Necessary Cables
8. testing and Reviewing the Cooler
9. Conclusion
10. Resources

Introduction

Are you tired of wasting your hard-earned money on products that don't deliver? Look no further, because I'm here to help make your life easier. In this article, I will guide you through the process of installing the Corsair H100 I Pro all-in-one water cooler on your AMD/Ryzen-based system. Before we begin, let's clear up some common questions about these types of coolers:

1. Do you need to fill these coolers with fluid or change the fluid?
2. Will it work with overclocking?
3. Is the installation different for every case?
4. Do the included fans have RGB lighting?
5. Can I ask questions answered in this video?

Now that we've addressed these questions, let's dive into the installation process.

Unboxing the Corsair H100 I Pro

Before we start the installation, let's take a look at what you'll find in the Corsair H100 I Pro Package. Inside, you'll find a warranty guide, which provides information on what is covered and an installation guide that we won't be using for this video. The package also includes two high-performance magnetic levitation fans, a USB cable for motherboard connection, mounting hardware for Intel and AMD sockets, an AMD mounting bracket, and a backing plate for Intel consumer-based sockets. The radiator is 240mm in size and comes with a thick design, which is impressive for an AIO cooler.

Installing the AMD Mounting Bracket

To begin the installation process, we need to convert the bracket for use with AMD sockets. Remove the Intel bracket and attach the AMD mounting bracket, making sure to fasten the hooks and thumb nuts just slightly, without tightening them all the way. Repeat this process on the other side of the bracket, ensuring proper orientation. Once that is done, you can install the bracket onto the water block by placing it in the holes and rotating it slightly until it clips into place. It's important to note that some motherboards may come with pre-installed brackets, so there's no need to remove them.

Attaching the Water Block and Pump Unit

The next step is to attach the water block and pump unit to the CPU. This part is easy – just hook one side of the block onto the bracket, lower down the other side, and hook it on as well. Be careful not to overtighten the thumb nuts at this stage. Once both sides are hooked on, you can fasten the thumb nuts to apply pressure to the CPU. It's normal for the water block to slightly bow out when tightened correctly, as this ensures proper clamping pressure.

Mounting the Fans to the Radiator

Now it's time to mount the fans to the radiator. Depending on your case, the airflow and installation may vary, but for this guide, we'll install the fans on the top of the radiator. Using the long screws provided, attach the fans to the radiator, ensuring a secure fit. This process should only take a minute or two.

Installing the Radiator to the Case

With the fans mounted, let's proceed to install the radiator in the case. Keep in mind that the mounting location might differ depending on your case. For our case, we'll be installing the radiator on the top. Use the short screws and washers provided to secure the radiator to your case. While installing the radiator, make sure to feed all the fan cables through to the back of the case. This will make cable management easier later on.

Plugging in the Necessary Cables

Once the radiator is in place, it's time to start plugging in the necessary cables to ensure the system functions properly. Locate a suitable spot on your motherboard to connect the fan speed controller, which will control the cooling performance. You can find ports labeled CPU opt, pump, or CPU fan for this purpose. Connect the fan speed controller to the chosen port.

Next, connect the USB cable to the pump unit, ensuring it clicks into the USB port on the pump. Thread the USB cable through the back of the case and find a USB header on your motherboard to plug it in. This will allow you to control the cooler through Corsair's IQ software.

Additionally, plug in any remaining cables that were passed through during the radiator installation. Once those are connected, use the SATA power connector to connect the cooler to an available SATA power cable from your power supply.

Testing and Reviewing the Cooler

Congratulations! The installation process is complete. Now you can test and review the Corsair H100 I Pro cooler. Monitor its performance and assess its effectiveness in keeping your CPU temperatures low. In our experience, this cooler has shown promising results. Its sturdy build and sleek design make it a great addition to any system. We may even consider conducting a more detailed review of this cooler in the future.

Conclusion

Installing the Corsair H100 I Pro all-in-one water cooler on your AMD-based system doesn't have to be a daunting task. By following the steps outlined in this guide, you can easily achieve optimal cooling for your CPU. The package includes all the necessary components, and the installation process is straightforward. Once installed, the cooler delivers excellent performance and adds to the overall aesthetics of your system.

Now that you have the knowledge and skills required, it's time to take the plunge and enhance your cooling setup. If you have any further questions or need assistance during the installation process, feel free to ask in the comments section below or join our community on Discord for more support.

Resources

• Corsair H100 I Pro Official Website

FAQ

Q: Do I need to refill or service the Corsair H100 I Pro cooler?
A: No, these coolers come pre-filled and do not require any fluid changes or servicing.

Q: Can I use the Corsair H100 I Pro for overclocking?
A: Yes, the H100 I Pro is designed to handle overclocking and provide efficient cooling for high-performance systems.

Q: Will the installation process be the same for all cases?
A: No, the installation process may vary depending on your case design. Refer to your specific case's manual for instructions.

Q: Do the included fans have RGB lighting?
A: No, the included fans with the Corsair H100 I Pro do not have RGB lighting.

Q: Where can I purchase the Corsair H100 I Pro?
A: You can purchase the Corsair H100 I Pro directly from the official Corsair website or through various online retailers.